11

Operation of Bending Machine of Control Bus Processing Machine

Release time :

2023-10-09 17:49

If you want to get a perfect bend, there are several key steps you should take when setting up the busbar processing machine bending machine. I like to think of these steps as links in the drive chain, you process one piece at a time to make sure they are safe before entering the next one. If everything is in place, the drive chain will be firm and functioning properly.

The distance changes the bend angle. These are not critical for larger V-die openings. To illustrate this, imagine separating two barrels by 30CM and placing a piece of light steel on top of them. If you push down about 3cm in the center, you won't notice the degree change in the material. If you then move the barrel only 3CM and push it down the same distance in the center, you will see a greater degree change.

For example, if you bend 20 gauge materials on a V-shaped mold with 1/4CM openings, and your accuracy is only 2‰ MM different, then your bending will change! Correctly setting up the bus bar processing machine bending machine through the following steps will help you obtain accurate bending results:

Calibration. The first thing you should do is to check and make sure that your brakes are properly calibrated. Verify that the plunger (Y axis) of the brake is correctly referenced, which means that it will repeat to the same Y position (or depth) every time it cycles. Also check to determine if it needs to be raised to avoid material deformation. By performing a test bend, you can see if the middle of the material is wider or narrower than the ends. If your 90 ° bend bends outward like a canoe in the middle, the material is deflected and convexity compensation is required.

Previous Page

Types of busbar processing machine

Maintenance and Maintenance of CNC Bus Processing Machine

Next Page

Previous Page

Types of busbar processing machine

Next Page

Maintenance and Maintenance of CNC Bus Processing Machine

RELATED NEWS

What are the characteristics of CNC bus processing machine?

The machine is equipped with three processing units of punching, cutting and folding, and the busbar can be punched, cut and folded separately or simultaneously through the operation screen or foot switch. The use of this machine high production efficiency, easy to use.

2023/10/09 17:24

How to control the CNC bus bending machine troubleshooting?

Now more and more bending machines have touch screen controls, and the cleanliness of the screen will affect the performance of the controls. We found that many operators think there is a problem with their screen, and recalibrating and cleaning it when the screen gets dirty can solve the problem. People have natural oils in their fingers and dirty their hands when loading the busbar processor, all of which will leave a film under their control. You can regularly clean the touch screen with a soft cloth such as a microfiber cloth to avoid problems.

2023/10/09 17:58

The use of three-in-one bus processing machine

Before use, the product can be compressed for a few times to discharge the air in the fuel tank. This time, full air pressure is prohibited. For example, when using the cutting and arranging machine for air pressure, first set the "black" handle to the "cutting and arranging" state, and operate the foot pedal switch of the electric pump. when the electric pump starts to operate, you can see that the upper knife of the cutting and arranging machine moves downward at the same time, and turn off the foot pedal switch. When air pressure is prohibited, the upper knife stroke to the bottom of the lower knife; The punching machine also operates as above. When using the vertical bending machine, first change the "black" handle to the "bending row" state. If you want to bend flat, change to the flat bending die. If you want to bend vertically, change to the vertical bending die.

2023/10/10 09:46

Development of CNC System for Bus-bar Angle Milling Machine

Networking and intelligent: the network of numerical control system is based on the current Internet technology to realize the remote monitoring and maintenance of numerical control system, even remote operation and processing, scheduling and management of production workshop, etc. Intelligent is to achieve automated production and processing, reduce human intervention in the production and processing process and the pursuit of the goal, with the use of more advanced controllers and various sensors, can make the machine tool in more secure conditions to achieve intelligent machine tools. In the program design, the user tries to operate less, and make the operation interface more "fool", in line with the thinking habits of most people, to achieve intelligent operation and friendly man-machine interface.

2023/10/09 18:12